Description

DIY Kit QRP Manual Antenna Tuner Tune 1 - 30Mhz 15W For HAM RADIO * CW Product Description: Can tune to the original non-resonant antenna by adding the appropriate inductance or capacitance so that the radio can work properly. The original resonant antenna, the antenna has changed due to outside influences, the SWR can be amended. Can be used as a band-pass filter, the emission can reduce unnecessary radiation outside the band, the cross-modulation and interference-band receiver can be reduced again. Days tune kit comes with the standing wave directions, using a T-type topology network, shortwave 1-30MHz, can withstand the transmit power of 15W, the tuning range of approximately 40-300 ohms, can be very convenient for QRP communication, to ensure high efficiency radio transceiver in communication, but also allows you to fully enjoy the fun of DIY. This kit requires some soldering electronic technology, will recognize the device, it will weld, the basic need debugging, as long as careful assembly according to package instructions can succeed. This kit welding, making easy to understand, easier to learn, easy to use. Comes with standing instructions, Q9 type interface (such as the need to be self to M-type interface), using T-topology networks, QRP facilitate communication with the low-power transceiver (shoes, frogs, octopus, etc.) used to make transceiver and antenna valid match, meet your emission requirements, ensure a highly efficient radio communications. Key Features of this manual antenna turner: Days when exposed to direct transfer power: Day tune tuning the input power: Tuning indication: LED display Interface: Q9 type Operating frequency: 1-30MHz Antenna Interface: Q9 type Match the antenna impedance range: about: 30 ~ 300Ω Carrying RF power: less than 15W Tuning required RF power: less than 3W This kit includes the original as follows: A waterproof sealed box Stickers (used to determine the position of the transfer hole) 1 Q9 Block (lug) 2 Ordinary wire segment Variable capacitor 2 2 small knob 0.25 countersunk head screws (for fixed variable capacitor) 4 The 0.25 head screws 2 0.3 gasket 4 0.3 nut 2 Multi-knife switch (12 stalls) a A large knob T106-2 the toroid (red) 1 0.5 enameled wire, Section 1, A circuit board (standing wave indicator) A stall switch The red light emitting diode 1 51 ohm 2W resistor 3 FT37-43 toroid (Black) 1 1K resistor (light-emitting diode current limit) a 1N60 1 0.1u capacitor 1 Payment Shipping Refund Payment EBAY Managed Payment. But we only Accept your Ebay Address, please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping 1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand. 2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders. 3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund. Refund If you can't receive the product within 2 months (60 days), please contact with us,we promise to payback 100% of your money. We ensure our products work normally before post.If the products is broken before arrival to you,all you should do is taking a photo to show us our broken product.We promise to payback 100% of your money. If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.